Different solutions for different purposes 

1)The Performance airfilter , exelent performance and max. protection. No copy of the std. filter , always searching for solutions , either it’s the performance , protection or fitment . Caution: clean and re-oil at least once a year with MWR airfilteroil & cleaner . Remapping the ECU or the Fuel Control Module is recommended.

2) The High Efficient airfilter for road & race bikes , designed for inletnoise reduction . The revolutionary High Efficient Airfilter is designed to reduce intake noise and yet more power to deliver.This design of airfilter has shown a reduction of up to 8db of intake noise compared to other sportsfilters.
Unlike all other sportsfilter all inlets will get with this High Efficient Airfilter the same quantity of air, regardless the speed of the motorcycle or wind directions . No different fuel-mappings between internal & external or front & rear cilinders are needed , this will be achieved by tuning each cylinder seperate . Caution: clean and re-oil at least once a year with MWR airfilteroil & cleaner . Remapping the ECU or the Fuel Control Module is highly recommended.

For some extra power you can replace the original airbox side covers for this powerkit.

BLUE LINE : OTHER SPORSTFILTER

RED LINE : MC-050-08HE

‘12/’22 KTM 690 SMC R 690

‘16/’22 Husqvarna 701 Supermoto

‘08/’11 KTM 690 SMC 690

MWR has developed a performance air filter where you can remove the original filter cover or the KTM performance cover. You can install the filter without these covers for maximum airflow / performance . The plate on top of the airfilter is to protect the filter from water / rain.

Note :Remapping ECU is necessary

‘08/’22 KTM 690 Enduro R 690

‘16/’22 Husqvarna 701 Enduro

MWR has also developed an enduro filter in this same range, this filter has a dual layer foam configuration which offers maximum protection in off-road terrain. Also for this filter it applies that the original cover or the performance cover are removed, installation of the MWR filter is without these covers for maximum airflow / performance. The plate on top of the airfilter is to protect the filter from water / rain .

Note :Remapping ECU is necessary

The performance airfilter needs to be installed with the printed logo directed to the Velocity Stacks , the "HE" filter need to be installed with the plate directed to the Velocity Stacks

With the MC-050-14HE filter check the fueling between front & rear cylinder

To increase the power for the highly restricted RC 125/200/250/390 '15/'18& Duke 125/200/250/390 '12/'16 , MWR developed a power-up kit for these bikes . Remove the toplid of the airbox and replace it with the MWR filterholder , maximum airflow & maximum performance is achieved.

This airfilter is not developed to reduce the inletnoise . Remapping the ECU or the Fuel Control Module is highly recommended.

The MWR performance filter for the 2017/2018 KTM 125/200/250/390 Duke models has the same construction as the very succesfull  MC-050-15 .

The more then 50% increased surface of the filter secures much better performance outcome and better protection

MC-050-18 : MWR Performance Airfilter for the KTM 790 , installation is the same as OEM filter but printed MWR logo in direction of the engine intakes

MC-055-18 : Power-up kit for the KTM 790 , will make a hugh difference in power with this extra opening . No modifications needed , replaces the original top-lid of the airbox .

Original top-lid out – MWR power-up kit in

Caution: Remapping the ECU or installation of a fuel module is necessary with open exhaust

.......................................................................................................

High performance MWR velocity stacks for the new ’21/’22  1290 KTM Super Duke R / SP

↑ For installation you don’t need the O-ring anymore to fit the upper injectors onto the stacks ↑