1)The Performance airfilter , exelent performance and max. protection . No copy of the std. filter , always searching for solutions , either it’s the performance , protection or fitment . Caution: clean and re-oil at least once a year with MWR airfilteroil & cleaner . Remapping the ECU or the Fuel Control Module is recommended.

2) The High Efficient airfilter for road & race bikes , designed for inletnoise reduction . The revolutionary High Efficient Airfilter is designed to reduce intake noise and yet more power to deliver . This design of airfilter has shown a reduction of up to 8db of intake noise compared to other sportsfilters.
Unlike all other sportsfilter all inlets will get with this High Efficient Airfilter the same quantity of air, regardless the speed of the motorcycle or wind directions . No different fuel-mappings between internal & external or front & rear cilinders are needed , this will be achieved by tuning each cylinder seper . Caution : clean and re-oil at least once a year with MWR airfilteroil & cleaner . Remapping the ECU or the Fuel Control Module is highly recommended.

Blue line : std bike + std filter
Red Line : std bike + MWR filter MC-060-10HE

Blue line : std bike + std filter
Red Line : std bike + MWR filter MC-060-10HE + Microtec M277 ECU + Costum mapping ( X-Bikes)

CAUTION : TO INSTALL THIS HIGH EFFICIENT AIRFILTER YOU MUST MODIFY YOUR AIRBOX

INSTUCTIONS AND PICTURES ABOUT THIS MODIFICATION SEE BELOW

 AIRBOX MODIFICATION  MV AGUSTA F4 2010 / 2012 FOR INSTALATION MWR HIGH EFFICIENT AIRFILTER

F3  675 / 800  +  EURO4 '17/'22

BRUTALE 675 / 800  +  EURO4 '17/'22

STRADALE 800  +  EURO4  '17/'22

RIVALE 800  +  EURO4  '17/'22

DRAGSTER 800  +  EURO4  '17/'22

TURISMO VELOCE 800  +  EURO4  '17/'22

Red line : std bike + std airfilter

Blue line : std bike + MWR airfilter MC-060-12R

MWR  developed in coorporation with profesional raceteams / MC Agusta RC  the MC-066-12 / MC-066-12R / MC-066-12WSBK for the road & racebikes.
TIP: To maximize the ram-air effect ( and max. power) remove the protectiongauze at the front of the airtubes.
NOTE:Remapping the ECU or installation of a fuel devise is necessary.

Visit our »Facebook«  page for more details.

MC-066-12 / MC-066-12R / MC-066-12WSBK INSTALLATION

Remove fuel tank to obtain access to the airbox ensure all pipes and leads are released before fully lifting the tank. The fuel pipe release is located on the left hand side behind the frame. The fuel pump lead is fitted directly into the fuel pump on the right side of the fuel tank base.

Remove all the retaining screws from the lid of the airbox please note the sensor on the left side  has a serrated washer.  Remove the air pressure sensor lead from the front of the airbox top and place it in a safe location.

Remove the original MV Agusta air filter, this can be achieved by simply cutting the filter into two parts if no longer required, alternatively  remove the three bolt retaining the air tube to allow the original filter to be removed.

You are now ready to install the MWR  air filter. You will see opposite the two air intakes two protruding  flat vertical plates. The plates are to be used to secure the MWR filter into its correct design location with the dome to the rear of the air box (WSBK filter).

Place the MWR filter into the location pictured , ensure the location points on both sides of the filter and securely mounted into the two vertical plates by dropping it into position , the four bent hooks on the filter must hold the filter in place. You will see a lip on the base of the airbox ensure the filter is placed at the front to complete the fitment of the filter fully.

Once completed simply reverse the procedure.

MWR developed in coorporation with MV Agusta RC / Profesional Raceteams the MC-066-12 / MC-066-12R / MC-066-12WSBK for the road & racebikes
TIP: To maximize the ram-air effect ( and max. power) remove the protectiongauze at the front of the airtubes
NOTE:Remapping the ECU or installation of a fuel devise is necessary.

This is a full race filter what needs more frequent the cleaning service , not recommended for the Brutale / Dragster / Rivale / Stradale & Turismo Veloce

Visit our »Facebook«  page for more details.

With the XXL airtubes we increased the inlet opening of the airbox , as you can see on picture3 the MWR Airtubes replace the original highly restricted airtubes to provide the engine with more air through the much larger holes.

Replacement airtubes for the original airtubes ,Installation of the tubular original filter or sport filters is no longer possible

Fits all Brutale / Rivale / Stradale / Dragster & Turismo Veloce 675/800 + EURO4 MODELS

High Performance Velocity Stacks fit  : F3 675 / 800 , BRUTALE 675 / 800 EURO3 , STRADALE 800 EURO3 , RIVALE 800 EURO3 , DRAGSTER 800 EURO3 , TURISMO VELOCE 800 EURO3 .

The MC-060-13 is to install without modifications ,includes bolts & spacers

Caution: For installation ONLY use the enclosed bolts , when fitting the filter for the first time you must press the bolts into the alu frame , also the enclosed spacers will be pressed into the alu frame from the other side.

For more info about the installation check our »Facebook«

Like with the MY2010 / MY2011 & MY2012 the peculiar tube has to be removed by installing the High Efficient or the Full Racefilter from the top-lid of the airbox.

Caution : For installation ONLY use the enclosed bolts , when fitting the filter for the first time you must press the bolts into the aluminium frame , also the enclosed spacers will be pressed into the alu frame from the other side.

When installing the filter for the first time the attached bolts & spacers must be pressed into the aluminium filter frame because of the angle of the bolts against the filter .

For more info about the installation check our »Facebook«

Like with the MY2010 / MY2011 & MY2012 the peculiar tube has to be removed by installing the full racefilter from the top-lid of the airbox.

Caution : For installation ONLY use the enclosed bolts , when fitting the filter for the first time you must press the bolts into the aluminium frame , also the enclosed spacers will be pressed into the alu frame from the other side.

When installing the filter for the first time the attached bolts & spacers must be pressed into the aluminium filter frame because of the angle of the bolts against the filter .

For more info about the installation check our »Facebook«